- Instrument Type
- 4-20mA Transmitters
- 0-5, 10V Transducers
- mV/V Sensors
- Digital Sensors
- Absolute Sensors
- ATEX Transmitters
- Calibration Pumps
- Calibrators
- Compound Ranges
- Digital Gauges
- Digital Manometers
- Digital Readouts
- DP Transmitters
- Indicators - Pressure
- Liquid Level Sensors
- Loggers - Pressure
- Loggers - Liquid Level
- Suction Pressure Sensors
- Switches
- Accessories
- Your Application
- Absolute Reference
- Air/Pneumatics
- Barometric/Atmospheric
- Certificates & Approvals
- Data Logging
- Differential
- Electrical Signal
- Flush Diaphragm
- Gauge Reference
- High Accuracy
- High Frequency Response
- High Range
- High Temperature
- Intrinsically Safe
- Leak Testing
- Level Measurement
- Low Ranges
- Measuring Range
- Media Compatibility
- Miniature
- OEM Design
- Overpressure Protection
- PC Interfacing
- Pressure Calibration
- Process Connection
- Testing
- Sensor Technology
- Submersible
- Temperature & Pressure
- Vacuum
- Water Level
- Water Pressure
- Your Industry
- Manufacturers
Improve the electrical termination of vented submersible pressure sensors
The KL1 termination enclosure is used to connect submersible cable at the top of a borehole or well to less expensive overground cables which run back to the control and monitoring station.Submersible cable is more expensive because it has to be reinforced to support the sensor plus its own wieight in deep holes without stretching which would lead to a change in sensor position and ultimately sensor calibration.
A submersible cable also has a vent tube running through it to allow gauge reference level transmitters to breath to ambient air pressure which is essential for accurate level measurement. Due to this extra complexity, submersible cable are more expensive than general purpose sensor cable and therefore the KL1 junction box helps reduce the cost of installations whilst providing a vent which prevents moisture ingress down the cable.
Although most instruments are not able to survive a direct lightning strike it is possible to protect nearby instrumentation from voltage surges which are less severe but can be just as damaging to sensitive sensor electronics without adequate discharge protection. The KL1 submersibe sensor junction box includes the option for protection from a 10 kiloamp discharge current.
If a PT100 temeprature sensor probe is included in the installation the KL1 terminal box can include an option for a PT100 transmitter to convert the output from a platinum resistance thermometer to a 2 wire, 4 to 20 mA output signal.
Related Products
More info for KL1 cable termination box
IP68 hydrostatic level transmitters
Digital readout Panel meters for level transmitters
Water level gauging tape for calibrating submersible level sensors
Associated Topics
Measuring liquid level in sealed tank
Reducing submersible hydrostatic pressure sensor failures
Calculating hydrostatic pressure ranges
Site Last Updated: 07/02/12
Glossary - Find explanations for terminology used in specifying and using pressure instruments
Pressure Conversion - Look up conversion factors or select a conversion table for a particular pressure unit
Pressure Measuring Guide - Collection of guidance notes for sourcing, setting up and using pressure measurement equipment
News Articles - Archive of application notes, product releases and technical information
Answers - Search for questions already answered or submit a new question about a pressure measurement topic or product
Pressure Sensor Specification - Select parameters with PSAT to generate a spec for your own use or to submit as an enquiry
Product Finder - Choose multiple product and application types to filter out a suitable product
- 27/03/09 : Measuring vacuum pressure with negative gauge or absolute pressure ranges
- 29/11/08 : What is the difference between a pressure transducer and a transmitter
- 15/09/08 : What is the difference between gauge and absolute pressure measurement
- 17/08/08 : What to consider when selecting a differential pressure sensor
- 10/02/08 : What affects the performance of low pressure sensors
- 19/01/08 : Supply voltage and load resistance considerations for pressure transmitters
- 06/01/08 : Measuring liquid level in a sealed tank with a hydrostatic pressure sensor
- 18/09/07 : Interpreting specifications of pressure sensor accuracy