Submersible Level Sensors

Hydrostatic level sensors which have IP68 submersible cable connections for permanent liquid immersion.

Economical IP68 protected sensor with stainless steel 316L housing and Ceramic strain gauge sensing diaphragm for measuring liquid depth pressure or the pressure in a submerged pipe or vessel. Measure hydrostatic pressure from from 0 to 10 mWC (33 ftWC) up to 0 to 100 mWC (330 ftWc) and convert reading to a millivolt, current or voltage signal output. The Ceramic diaphragm has a high chemical resistance to media such as leachate and seawater, and the housing can be upgraded to Duplex stainless steel if necessary for extra material protection. A PUR coated cable is fitted as standard, but for additional chemical protection an FEP coated cable can be supplied.

Hydrostatic level sensor with an IP68 sealed electrical connection, stainless steel 316L, Duplex or PVC construction and a passive millivolt strain gauge output signal. Available in level ranges from 10 to 100 mWG gauge or absolute.

Absolute referenced hydrostatic depth sensor with an IP68 sealed electrical interface, stainless steel 316L, Duplex or PVC housing and a mV, amplified voltage or current output. Available in depth ranges from 1 to 10 bar absolute.

Water resistant pressure sensor for measuring hydrostatic pressures in the range of 0-0.5 mWC up to 0-100 mWC. An all stainless steel 316L construction with Viton O rings seals and a choice of PUR, PVC or FEP vented cabling. The IMSL is used for measuring groundwater, aquifer, reservoir and borehole water level. The internal silicon strain gauge sensor provides a stable water level reading accurate to 0.1% of span linearity with low hysteresis and repeatability errors.

IP68 sealed hydrostatic level transmitter with a 17mm diameter for lowering into ground water boreholes for environmental monitoring of water level. Available in level ranges from 6 up to 200 metres of water gauge (650 ftH2O gage) with an accuracy of 0.5% full scale.

Submersible waste water level sensor with optional intrinsic safety certification for monitoring the level of sewage and effluent in water treatment plants. Available in level ranges from 4 up to 250 meters of water gauge.

Submersible Low Range waste water level transmitter with intrinsically safe option for monitoring the level of sewage and effluent in water treatment plants. Available in level ranges from 0.4 up to 100 meters of water gauge.

Marine approved level transmitter with 4-20mA current loop output for measuring the level of contents inside a ships ballast, fuel, liquid cargo or wastewater tanks with optional all CuNiFe construction for sea-water compatibility in ranges from 0.4 mH2O to 200mH2O gauge or absolute.

IP68 mid range pressure transmitter for measuring the level of highly contaminated and agressive liquid media with a body made from PVC. Hydrostatic ranges from 4 mWC up to 100 mWC

IP68 low range pressure transmitter for measuring the level of highly contaminated and agressive liquid media with a body made from PP (Polypropylene) or PVDF. Hydrostatic level ranges from 0.4 up to 100 metres of water column.

Submersible stainless steel pressure transmitter ideal for geotechnical surveying with a 19mm diameter for measuring hydrostatic water level in bore-holes. This small diameter level sensor has level ranges from 1 up to 250 metres water column and a 4-20mA current loop output signal.

Submersible level transmitter for measuring liquid level with a 4-20mA current loop or a 0-10V voltage output plus optional ATEX approval for instrinsically safe use in hazardous areas in ranges from 1mH2O up to 250mH2O.

SDI-12 protocol transducer for sensing water depth level and temperature in seawater, brackish water, tidal water, saline water or leachate. The digital interface conforms to the requirements of the SDI12 support group and can be used with environment monitoring equipment which supports the SDI12 digital communications interface. A high corrosion resistant ceramic diaphragm is fitted a standard and stainless steel 316L, Duplex or Marine Bronze housing materials can be chosen to suit the application requirements. Measure salt water depth in the ranges starting from 0-10 metres up to 0-100 metres, including absolute non-vented ranges from 1.5 bar up to 10 bar absolute.

Combined pressure and temperature sensor with a 1200 baud rate serial data interface as defined by the SDI-12 support group. The S12S is a submersible probe used for monitoring water level and temperature. The SDI-12 digital interface is specially designed for low power, battery operated instrumentation such as on-site environmental dataloggers. Measure the rise and fall of water levels in ranges from 0 to 2 feet up to 0 to 300 feet of water column.

Analogue output sensor for immersing in seawater to determine depth or change in water level by measuring hydrostatic pressure. This sea depth probe has a Marine bronze housing and Ceramic diaphragm for protection from saltwater corrosion. Select fixed ranges from 10 metres (33 feet) up to 100 metres (328 feet) depth in a number of analogue output configurations including low voltage strain gauge, amplified voltage and current loop output. Also suitable for use in brackish and inland tidal water or any other application where there is the risk of corrosion form a saline liquid.