Strain Gauge Output

Sensing devices with a wheatstone bridge strain gauge circuit that produces a low voltage mV signal without any amplification.  Select a device with a output sensitivity that is proportional to the input supply voltage.

Piezo-resistive pressure transducer with a 2mV/V or 10mV/V output signal in pressure ranges from 1 bar up to 700 bar gauge or absolute.

Motorsport pressure transducer with 21mm diameter and and 24mm body length for pressure ranges from 0.5 up to 400 bar gauge or absolute. Available with millivolt and amplified voltage output signals covering the majority of motorsport analogue input signals.

Miniature size 1/2 inch diameter stainlesss steel pressure sensor with either a strain gauge millivolt output or an amplified 0.5 to 4.5 Vdc output. Pressure ranges start from 10 bar (150psi) up to 400 bar (6000 psi). Thread sizes include M5, M6, M8, M10, Dash3 or 1/8NPT.

Half in inch diameter sensor for measuring both temperature and pressure in one device. Measure pressure in ranges from 0-150 psi up to 0-6000 psi. Select a NTC thermistor, PT100 or PT1000 temperature measurement device to integrate alongside the pressure sensing device.

Hydrostatic level sensor with an IP68 sealed electrical connection, stainless steel 316L, Duplex or PVC construction and a passive millivolt strain gauge output signal. Available in level ranges from 10 to 100 mWG gauge or absolute.

Absolute referenced hydrostatic depth sensor with an IP68 sealed electrical interface, stainless steel 316L, Duplex or PVC housing and a mV, amplified voltage or current output. Available in depth ranges from 1 to 10 bar absolute.

Versatile low price pressure transducer with a wide selection of electrical and mechanical options to enable the customisation of the sensor to suit most industrial, automation and OEM design installations. A dry cell ceramic strain gauge sensing diaphragm provides a high corrosion resistance to many types of harsh chemical media commonly found in automated industrial processes and machinery monitoring applications.

Water resistant pressure sensor for measuring hydrostatic pressures in the range of 0-0.5 mWC up to 0-100 mWC. An all stainless steel 316L construction with Viton O rings seals and a choice of PUR, PVC or FEP vented cabling. The IMSL is used for measuring groundwater, aquifer, reservoir and borehole water level. The internal silicon strain gauge sensor provides a stable water level reading accurate to 0.1% of span linearity with low hysteresis and repeatability errors.

Economical pressure transducer for monitoring fluid level inside a tank wehre there is no external mounting point at the bottom of the tank. Measure liquid contents of tanks with heights from 0.5 metres (1.64 feet) to 10 metres (32.8 feet) high. Choose between a low powered millivolt output, 0.5 to 4.5 vdc signal or a process control 4-20mA current loop signal.

IP68 protect pressure sensor for monitoring fresh water level to depths of 100 metres. This stainless steel drinking water compatible level sensor has been assesed and certified by the Water Regulations Advisory Scheme (WRAS) for compliance with the UK water regulations. The materials and fittings used in the mechanical construction of the IWSL water level sensor meet the standards required by the water supply byelaws of England, Wales and Scotland.

Passive compensated pressure transducer with a four arm semiconductor Wheatstone bridge circuit which produces a 100 millivolt with a 10 volt excitation. Pressure ranges from 0-100mbar up to 0-1000bar gauge or absolute. The silicon sensing chip is totally isolated from the media by an oil filled stainless steel 316L capsule with isolation membrane. This sensor is ideally suited for high frequency response applications since the output is only limited by the natural response of the silicon sensing capsule.

Piezo-resistive pressure sensor with a millivolt output direct from a four arm wheatstone bridge strain gauge circuit in pressure ranges from 10 up to 1000 bar gauge.