Pressure sensors & instrumentation for measuring pressure & level in water pipes, boreholes, reservoirs, weirs and open channels.
Economical IP68 protected sensor with stainless steel 316L housing and Ceramic strain gauge sensing diaphragm for measuring liquid depth pressure or the pressure in a submerged pipe or vessel. Measure hydrostatic pressure from from 0 to 10 mWC (33 ftWC) up to 0 to 100 mWC (330 ftWc) and convert reading to a millivolt, current or voltage signal output. The Ceramic diaphragm has a high chemical resistance to media such as leachate and seawater, and the housing can be upgraded to Duplex stainless steel if necessary for extra material protection. A PUR coated cable is fitted as standard, but for additional chemical protection an FEP coated cable can be supplied.
All stainless steel 316L hygienic digital display pressure gauge for measuring low range pressures with ranges from 0-100 mbar up to 0-40 bar gauge or absolute, including vacuum range 0 to -1 bar. This sanitary pressure gauge includes open diaphragm process fittings for threaded BSP, dairy pipe and Tri-clamp style process connections.
Immersible low pressure sensor for measuring shallow liquid level with a rangeable 4-20mA current loop or high level voltage output signal in level ranges from 80mmH20 up to 160mH2O
Low price digital pressure gauge with an accuracy of 0.5% pressure range for general purpose industrial measurements. Measure the pressure of fluids or gases in a range of pressures from the lowest range of 0 to 1.6 barg up to the highest range of 0 to 250 barg. For convenient mounting the pressure gauge includes a positionable display to ensure the reading is horizontal and pointing in the most easily viewed direction for the user. There is also the choice of a fixed 1/4 inch BSP parallel or 1/4 inch NPT male tapered thread and a choice of 4 popular pressure units selectable by the user.
Wet wet differential pressure sensor with a high overpressure rating on both positive and negative side port for protection against accidental diaphragm damage. The DMD 331 has 6 nominal pressure range from 0-0.2 bar up to 0-16 bar differential and each range has a choice of sub-ranges which can be selected depending on the required level of overpressure rating. The differential pressure signals can be transmitted as linear 4-20mA or 0-10Vdc analog output.
Three in one hydrostatic level switch, digital level gauge and level sensor with level ranges from 1 mWG up to 600 mWG (3.3 to 1969 ftWG).
Measure vacuum, positive gauge and absolute pressures from -1 bar (-15psi) up to 40 bar (600psi) with this all in one electronic switch, gauge and sensor. Designed specifically for use in the food, drink and biomedical industry for measuring process pressures and vessel contents. Choose dairy pipe or clamp type sanitary process fittings and select a food grade oil fill as the diaphragm isolation fluid. For pharmaceutical installations requiring hazardous dust protection the instrument includes the option for ATEX intrinsic safety.
IP68 combined liquid level and temperature, dual 4 to 20 milliamp output pressure sensor with a 316L or Duplex stainless steel housing and a high corrosion resistant ceramic sensing diaphragm. The IMCTL is available with ranges starting from 10 mWC (33 ftWC) to a maximum range of 100 mWC (330 ftWc) and can measure temperature over a choice of four different scaled ranges between -20 to +60 degC.
Versatile low price pressure transducer with a wide selection of electrical and mechanical options to enable the customisation of the sensor to suit most industrial, automation and OEM design installations. A dry cell ceramic strain gauge sensing diaphragm provides a high corrosion resistance to many types of harsh chemical media commonly found in automated industrial processes and machinery monitoring applications.
Water resistant pressure sensor for measuring hydrostatic pressures in the range of 0-0.5 mWC up to 0-100 mWC. An all stainless steel 316L construction with Viton O rings seals and a choice of PUR, PVC or FEP vented cabling. The IMSL is used for measuring groundwater, aquifer, reservoir and borehole water level. The internal silicon strain gauge sensor provides a stable water level reading accurate to 0.1% of span linearity with low hysteresis and repeatability errors.
Stainless steel 316L waterproof probe for measuring both water temperature and depth and generating two separate 4-20mA current loop measurement signals. Select temperature measurement ranges from -20 to +60 deg C and depth ranges of 0-0.5mWG to 0-100mWG.
IP68 protect pressure sensor for monitoring fresh water level to depths of 100 metres. This stainless steel drinking water compatible level sensor has been assesed and certified by the Water Regulations Advisory Scheme (WRAS) for compliance with the UK water regulations. The materials and fittings used in the mechanical construction of the IWSL water level sensor meet the standards required by the water supply byelaws of England, Wales and Scotland.
Robust cable junction box for terminating vented electrical cable from a 2 wire submersible hydrostatic level transmitter. The inside of the IP66 sealed box is vented to the ambient outside air via a PTFE filter to ensure the level sensor is properly vented to compensate for atmospheric pressure.
Combined digital manometer and pressure data logging instrument for recording pressures and temperatures which can store up to 57,000 readings in the non-volatile memory with a battery life of up to 5 years.
Battery powered digital gauge with an accuracy of 0.2% full scale in pressure ranges from -1 to 3 bar up to 1000 bar. The LEO 1 digital pressure gauge features 6 pressure units, rotatable display, zero tare & peak hold display functions and optional ATEX approval for intrinsic safety.
Handheld battery powered digital manometer in pressure ranges from -1 to 3 bar up to 700 bar with an accuracy of 0.2% full scale with 6 pressure units, zero tare & peak hold display functions and optional ATEX approval for intrinsic safety
LCD digital pressure gauge powered externally by a 2 wire series 4-20mA current loop or a digital interface. Use as a pressure transmitter or a digital output pressure sensor with a local readout display. Accurate to 0.2% FS the LEO3 is available in a sleection of pressure ranges from -1 to 3 bar up to 1000 bar (-15 to 45 psi up to 15,000 psi).
IP68 sealed hydrostatic level transmitter with a 17mm diameter for lowering into ground water boreholes for environmental monitoring of water level. Available in level ranges from 6 up to 200 metres of water gauge (650 ftH2O gage) with an accuracy of 0.5% full scale.
Submersible waste water level sensor with optional intrinsic safety certification for monitoring the level of sewage and effluent in water treatment plants. Available in level ranges from 4 up to 250 meters of water gauge.
Level pressure sensor with semi-flush ceramic diaphragm and stainless steel or PVDF wetted parts for aggressive corrosive media in ranges from 4mH2O up to 600mH2O gauge.
Flush capacitive ceramic pressure sensor for measuring corrosive and viscous liquid level from levels 0.4 metres of water up to 200 mH2O. This screw-in fluid level transmitter features high overload rating up to 50x and options for all plastic wetted parts.
Submersible Low Range waste water level transmitter with intrinsically safe option for monitoring the level of sewage and effluent in water treatment plants. Available in level ranges from 0.4 up to 100 meters of water gauge.
Marine approved level transmitter with 4-20mA current loop output for measuring the level of contents inside a ships ballast, fuel, liquid cargo or wastewater tanks with optional all CuNiFe construction for sea-water compatibility in ranges from 0.4 mH2O to 200mH2O gauge or absolute.
IP68 mid range pressure transmitter for measuring the level of highly contaminated and agressive liquid media with a body made from PVC. Hydrostatic ranges from 4 mWC up to 100 mWC
IP68 low range pressure transmitter for measuring the level of highly contaminated and agressive liquid media with a body made from PP (Polypropylene) or PVDF. Hydrostatic level ranges from 0.4 up to 100 metres of water column.
Submersible stainless steel pressure transmitter ideal for geotechnical surveying with a 19mm diameter for measuring hydrostatic water level in bore-holes. This small diameter level sensor has level ranges from 1 up to 250 metres water column and a 4-20mA current loop output signal.
Submersible level transmitter for measuring liquid level with a 4-20mA current loop or a 0-10V voltage output plus optional ATEX approval for instrinsically safe use in hazardous areas in ranges from 1mH2O up to 250mH2O.
Plug-on digital display for adding a local indicator to a pressure or liquid level sensor with a 4-20mA or 0-10Vdc output. No extra power supply is required since the PA430 is powered by the sensor supply. Mix and match Binder, M12 electrical and DIN plug and socket connector types. Optional ATEX IS approval for hazardous areas and 1 or 2 contact PNP switches for on/off process control function.
SDI-12 protocol transducer for sensing water depth level and temperature in seawater, brackish water, tidal water, saline water or leachate. The digital interface conforms to the requirements of the SDI12 support group and can be used with environment monitoring equipment which supports the SDI12 digital communications interface. A high corrosion resistant ceramic diaphragm is fitted a standard and stainless steel 316L, Duplex or Marine Bronze housing materials can be chosen to suit the application requirements. Measure salt water depth in the ranges starting from 0-10 metres up to 0-100 metres, including absolute non-vented ranges from 1.5 bar up to 10 bar absolute.
Combined pressure and temperature sensor with a 1200 baud rate serial data interface as defined by the SDI-12 support group. The S12S is a submersible probe used for monitoring water level and temperature. The SDI-12 digital interface is specially designed for low power, battery operated instrumentation such as on-site environmental dataloggers. Measure the rise and fall of water levels in ranges from 0 to 2 feet up to 0 to 300 feet of water column.
Rangeable DP Cell current loop process transmitter for monitoring differential pressures in a heavy duty process plant environment. The XMD has a standard process configuration with kidney flange mounting arrangement and large accessible electronic housing. Other features include ATEX intrinsic safety or flameproof, linear or square root extraction 4-20mA output, HART communications, 10 to 1 turndown ranging, LCD readout and 130 bar overpressure protection on one side.
Process transmitter for measuring vacuum, steam, food, pharmaceutical, oil, gas and other pressure readings necessary for the monitoring and control of bulk production processes. Suitable for deploying in many locations and feeding pressure readings back to the site distributed control system (DCS). Includes HART protocol interface, 10:1 adjustable range scaling and ATEX intrinsic safety as standard, with options for flameproof, 300degC media temperature and integrated local digital indicator. Available in pressure ranges from 0-400mbar up to 0-600 bar gauge or absolute, and compound ranges from -0.4 to +0.4 bar up to -1 to 10 bar gauge.
tel: +44 (0)844 800 9440
©2013 SensorsONE Ltd, all rights reserved.